Search Results for: engine for motorcycle

Starter Motor GAK50 Starting Engine Motorcycle Scooter Kit

NameGAK50 Starter Motor
TypeStarter Assembly
Car MakeMotorcycle/Scooter/Go kart
Model NumberGAK50 Starter Motor
Warranty1 Months
Overall Length100 mm
Overall Width85mm
Overall Height60mm
MaterialMetal
Net weight0.35 kg
ApplicationMotorcycle/Scooter/Go kart
CpnoQDMD.00016
Contact Us

Replaces Rear Disc Brake Calliper with Hose For Motorcycle Engine Kit

NameDisc Brake Kit
Model NumberDisc Brake Kit
Warranty1 Months
Distance Between Fixing Holes44mm
Calliper Overall Height64mm
Hose Length558.8mm
Diameter of Fixing Hole(s)6mm
Diameter of Handlebar Hole6mm
Total Length600mm
Distance Between Brake Pads4mm
weight1.35kg
FitPit Bike/Dirt Bike/go kart
Motorcycle ModelSpeedway
Contact Us

PZ30 Carburetor Fits for 200cc 250cc Motorcycle engine

Product NamePZ30 Carburetor
TypeCarburetor, PZ30 Carburetor
Usage200cc 250cc
MaterialAluminum/rubber
Net Weight0.54kg
Fits forDirt bike/ motorcycle
PackageCarton
CPNOHYQ.00152
Contact Us

Off-road vehicle motorcycle 50CC set cylinder assembly Engine cylinder head kit assembly 39MM cylinder diameter fittings

Product Name39mm Cylinder kit
Number of cylinderssingle cylinder
fuel consumption per 100 km2 L
torque39 (nm)
Applicable modelsmotorcycle 50 cc off-road vehicle
article numberTGZC-54
Size14×12.5x10cm
Weight1.94kg
CPNOQG.00027

How To Rebuild your ATV Master Cylinder

Step One
Carefully remove the twin Phillips head screws that hold the cap on and set the cover along with the diaphragm plate and rubber? diaphragm to the side for now. Be sure the handlebar is positioned so the master cylinder is as level as possible to avoid spills.Using a couple of paper towels or disposable shop rag dry up the fluid in the master cylinder until the majority of the old fluid is gone. Be very cautious as to where you dispose of these rags after they have soaked in the fluid. If these rub up against some metal or painted surfaces, things will start to corrode.

Step Two
To gain better access to the master cylinder for cleaning, remove the master cylinder from the handlebar by removing the two 8mm bolts that keep it in place.
Step Three
Loosen the 10mm banjo bolt that holds the brake line to the master cylinder. Be sure to not lose the copper washers as you will need them once you start to put the system back together. You may want to wrap the line with an old shop rag just below the bolt as fluid remaining in the line could leak out. Loosen the two 8mm bolts that hold the brake master cylinder to the bars and pull the master cylinder from the bars.
Step Four
Remove the brake lever from the master cylinder by removing a single pivot bolt, which is held in by a locking nut. This will
allow you to see the plunger and rubber boot that covers the plunger. There is a snap ring that holds the plunger in place and you will need long thin snap ring bits to get down inside the cast body of the master cylinder to get it out. The old plunger, spring and seals should simply pull out of the master cylinder. You will also want to remove the black silicone seal inside the master cylinder to get any debris out from under it.
Step Five
Once everything is removed you are ready to completely clean the master cylinder. After it is prepped for the new plunger, spring and seals add a little coating of brake fluid to the seals. This should help the reinstall of the new plunger and spring.
Contact Us

NEW 12V STARTER MOTOR COMPATIBLE WITH HONDA MOTORCYCLE GL1000 GOLD WING LTD 76 999CC ENGINE 31200-371-005 31200-371-505 31200371005 31200371505

100% NEW and Made with the Highest Quality Components Available
Full One Year Warranty
Computer tested for consistent Quality and unsurpassed reliability

COMPATIBLE WITH:HONDA 31200-371-005 31200371005 31200-371-505 31200371505

PRODUCT NAME:STARTER MOTOR
VOLTAGE: 12 VOLTS
ROTATION: CW
TEETH/SPLINES: 31 TEETH/SPLINES
PINION/SPLINES OD: 13.6MM / 0.535IN
MOUNTING HOLE 1: 6.6MM ID UNTHREADED
MOUNTING HOLE 2: 6.6MM ID UNTHREADED
APPROXIMATE WEIGHT: 5.575 LBS / 2.53 KG
APPLICATIONS:PLEASE VERIFY YOUR OEM PART NUMBER FROM YOUR ORIGINAL UNIT TO HELP ENSURE FITMENT.

HONDA MOTORCYCLE GL1000 GOLD WING 79-76 999CC MITSUBA SYSTEM HONDA MOTORCYCLE GL1000 GOLD WING LTD 76 999CC MITSUBA SYSTEM

Motorcycle TH90 Engine Carburettor for sale

  • Name: TH90 Carburetor
  • Model: TH90
  • Engine type: Gasoline engine
  • Tpye: Engine/Generator
  • Weight: 0.4KG
  • Size: 12cmx8.8cmc7.2cn
  • Material: Iron
  • Fit for: Motorcycle Fuel System
  • Quality: High
  • Packing: Carton

  • Contact Us

Motorcycle spare parts bicycle engine piston kit

Warranty:3 Months
Type:PISTON
Certification:CE
Diameter:12mm
Car Model:motorcycle
Engine Code:cofirmed
Size:44mm 12mm
Name:49cc Piston Kit 44mm 12mm
Centre of Pin Hole to Crown:17.61mm
Crown Height:36mm
Gudgeon Pin Diameter:12mm
Gudgeon Pin Length:36mm
Lower Piston Diameter:43.95mm
Piston Height:40mm
Upper Piston Diameter:43.74mm

Contact Us

Motorcycle spare parts bicycle engine piston kit made in china factory

Name49cc Piston Kit 44mm 12mm
Warranty3 Months
TypePISTON
CertificationCE
Diameter12mm
Car Modelmotorcycle
Engine Codecofirmed
Size44mm 12mm
Centre of Pin Hole to Crown17.61mm
Crown Height36mm
Gudgeon Pin Diameter12mm
Gudgeon Pin Length36mm
Lower Piston Diameter43.95mm
Piston Height40mm
Upper Piston Diameter43.74mm
CPNOQGPJ.00002
Contact Us